Exhaust mount and throttle cable

Jeff Lund · 01-26-2010, 11:14 PM

I just ordered a new Rotax and need to buy all the accessories for the conversion. I didn't ask the right questions before ordering the exhaust mount and ended up getting a Prospeed mount that doesn't fit my '08 RX-30 SE. Does Freeline or anyone else make a Rotax exhaust mount for the RX-30?

Also what size throttle cable would I need for the Rotax? I'm competing at Carolina Motorsports Park, which I'm completely excited about since there was no club even close me in NC before CMP opened.

Chris Lobaugh · 01-27-2010, 09:14 AM

Jeff,
Yes Freeline does make an exhaust mount for the rotax max. They are billet aluminum and mount where the rear torsion bar would go. Part number is 20.7285.10-OR and you will need two of them. Along with those you will need two 20.4524.10 (30mm frame clamps), two 20.1612.06 (flat bracket), and then some sort of spacers to go between the pipe and bracket to get the proper height/fit of the exhaust pipe. The guys at CMP are up to speed and are using the same system to support the Rotax exhaust pipe. Let me know if there is anything else I can do to assist.

Chris Lobaugh · 01-27-2010, 09:25 AM

Throttle Cable: Freeline throttle cable part 8000.00.01
The cable is 5 ft. long and 1.2mm in diameter with a "ball" end.

Jeff Lund · 01-27-2010, 04:07 PM

Thanks Chris. I couldn't find any info on that stuff to save my life. You guys have been awesome!

01-26-2010, 11:14 PM	#1
Jeff Lund Rookie Join Date: Dec 2008 Location: Raleigh, NC Posts: 3	Exhaust mount and throttle cable I just ordered a new Rotax and need to buy all the accessories for the conversion. I didn't ask the right questions before ordering the exhaust mount and ended up getting a Prospeed mount that doesn't fit my '08 RX-30 SE. Does Freeline or anyone else make a Rotax exhaust mount for the RX-30? Also what size throttle cable would I need for the Rotax? I'm competing at Carolina Motorsports Park, which I'm completely excited about since there was no club even close me in NC before CMP opened.

01-27-2010, 09:14 AM	#2
Chris Lobaugh Birel Specialist / Engineer Join Date: Jan 2008 Posts: 217	Jeff, Yes Freeline does make an exhaust mount for the rotax max. They are billet aluminum and mount where the rear torsion bar would go. Part number is 20.7285.10-OR and you will need two of them. Along with those you will need two 20.4524.10 (30mm frame clamps), two 20.1612.06 (flat bracket), and then some sort of spacers to go between the pipe and bracket to get the proper height/fit of the exhaust pipe. The guys at CMP are up to speed and are using the same system to support the Rotax exhaust pipe. Let me know if there is anything else I can do to assist. __________________ Chris Lobaugh Birel Engineer & Specialist chris@mrpmotorsport.com

01-27-2010, 09:25 AM	#3
Chris Lobaugh Birel Specialist / Engineer Join Date: Jan 2008 Posts: 217	Throttle Cable: Freeline throttle cable part 8000.00.01 The cable is 5 ft. long and 1.2mm in diameter with a "ball" end. __________________ Chris Lobaugh Birel Engineer & Specialist chris@mrpmotorsport.com

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-27-2010, 04:07 PM	#4
Jeff Lund Rookie Join Date: Dec 2008 Location: Raleigh, NC Posts: 3	Thanks Chris. I couldn't find any info on that stuff to save my life. You guys have been awesome!